Rad Power Bikes error 25 appears on the display as a two-digit code, and the manual gives it two possible meanings: a brake switch fault, or the brake being applied while the bike is switched on. That second meaning is the useful one, because it turns the code into a test you can run in under a minute — release both levers, restart, and watch what happens.
This article works from the checks and figures that actually exist. Rad publishes no troubleshooting guide for error 25, only the manual definition, so every check below is traced to that definition, to Rad’s published connector method for its other codes, or is marked as not published. Definitions come from EbikePost’s guide to Rad’s error codes, drawn from Rad’s own 2019 RadWagon manual. This is part of our E-Bikes Hub guides.

What error 25 means, in numbers
Rad’s 2019 RadWagon manual (V4-004) lists six common codes: 21 abnormal current, 22 throttle fault, 23 motor phase fault, 24 motor Hall fault, 25 brake switch fault, and 30 communication fault. Error 25 carries the full manual wording “brake switch fault, or brake applied while turning on”. Rad’s Help Center has step-by-step guides for 21, 22 and 23 only; for 24, 25 and 30 there is no official guide — only the manual definition and the instruction to contact Rad. The manual’s blanket advice is to stop riding and contact Rad whenever a code is displayed. The list is confirmed for the 2019 RadWagon manual; newer models have their own manuals, so check yours.
Here is every check an owner can make, with what each result means. Two rows say “Not published” — Rad publishes no figure for them.
| Check | What you find | What it means | Source |
|---|---|---|---|
| Levers at switch-on | A lever is pulled in | Expected — the manual defines 25 as “brake applied while turning on” | RadWagon manual V4-004 |
| Levers at switch-on | Both levers fully released | Not the switch-on case; a switch or wiring fault | RadWagon manual V4-004 |
| Lever after you let go | Lever springs back fully | Travel is normal; the switch should have opened | Manual: “both brake levers are fully released” |
| Lever after you let go | Lever stays in or returns slowly | The switch may still be pressed | Owner check from the manual wording |
| Code after restart | Code clears | The fault was the switch-on state, not a failed part | Manual safe check |
| Code after restart | Code returns, levers released | Contact Rad — no further owner step is given | RadWagon manual V4-004 |
| Brake switch sensor voltage | — | Not published | Rad publishes no figure |
| LED flash pattern for 25 | — | Not published | Rad publishes patterns for 21, 22 and 23 only |
| Battery label | RP-1304, RAD-S1304Y or HL-RP-S1304 | Stop — CPSC fire-risk warning, 24 Nov 2025 | U.S. Consumer Product Safety Commission |
A worked example. A rider switches the bike on while holding the left lever to keep the bike steady, and the display shows 25. The table says the code is expected when a lever is pulled at switch-on, so this is the switch-on case, not a broken part. The rider switches off, lets both levers go, watches them spring back, then switches on again with hands off the levers. The code clears — no part is needed; the fix is a habit. Now the contrast case: the same test, levers fully released, and 25 comes straight back. The table has one answer for that row — the switch or its wiring is the suspect, and the manual gives no further owner step.
The checks, in order
Run these in order.
| Step | Do this | Expected result | If it is different |
|---|---|---|---|
| 1 | Check the battery label against RP-1304, RAD-S1304Y and HL-RP-S1304 | No match | If it matches, stop — the CPSC warning applies |
| 2 | Switch the bike off | Display goes dark | Display stays on — switch off at the battery and wait |
| 3 | Release both brake levers and watch them spring back | Both return fully and freely | A sticking lever is the fault to fix |
| 4 | Switch on with your hands off the levers | No code, or the code clears | Error 25 shows again — go to step 5 |
| 5 | Look, without unplugging the main wiring, at the cable near the lever and handlebar for pinching, crushing or wetness | Cable looks undamaged and dry | Pinched, crushed or wet cable — note it and contact Rad |
| 6 | Restart once more with levers released | Code clears | Code returns — contact Rad |
Step 5 is a look-only check. Rad’s guidance for its other codes tells owners to look at visible connectors and cables without touching the main wiring, and to note anything pinched, crushed or wet. Do not open the display, controller or battery to chase this code.
The causes, ranked
Most likely first, following the manual’s own wording.
- The brake was pulled while switching on. The manual’s own second definition, and the only cause Rad documents. It clears on a restart with released levers.
- A lever that does not return fully. A grip pressing on the lever, a stiff pivot or a tight cable can hold it a few millimetres in — enough to keep the cutoff switch pressed.
- A stuck brake switch inside the lever. The switch stays closed even after the lever returns. The cutoff switch is built into the lever, so a faulty switch usually means a new lever.
- The lever connector loose, damp or dirty. Rad’s guides for its other codes treat connector condition as the first physical check.
- A pinched or damaged cable at the handlebar. A cable crushed by a clamp, a strap or a fall can break the switch signal.
- A controller misreading the switch. Least likely, and not something an owner can confirm — the manual’s answer is to contact Rad.

Why the generic advice is incomplete
Most pages that list Rad’s error codes repeat the manual’s one line for 25 — “brake switch fault, or brake applied while turning on” — and stop there. That line is correct, but it is not a diagnosis: it does not say which of the two meanings applies to your bike. The test in this article, one restart with released levers, is the difference between the two, and it is missing from the lists.
Some lists make it worse by mixing the codes up: error 25 gets described as a throttle problem, or every code gets the same generic fix. The manual’s definitions differ for a reason — 22 is the throttle fault and 25 is the brake switch. Other lists quote figures that do not exist: a sensor voltage, a switch gap, a resistance reading. Rad publishes none of those figures for error 25, so any list that quotes one is inventing it; where this article has no figure, it says “Not published”. There is also a dead end: Rad’s older support-site code pages returned “page not found” when checked on 24 October 2026, so old links promising “Rad’s error 25 guide” lead nowhere.
When error 25 shows up
The most common moment is switch-on itself: you hold the bike steady by a brake lever while you press power, and the display answers with 25. That is the code working as the manual describes it, not a fault. The second is after the bike has been parked with a lever pressed — a brake locked on, a strap or a bag resting on the lever, or the bike leaning on its lever. The switch does not know why the lever is in; it only reports that it is. It can also appear after handlebar work, since the lever connector sits at the handlebar, and after a wet ride, when Rad’s guidance for its other codes has owners check connectors for moisture. If it first appears right after a fall or a knock to the handlebar, check the lever itself — a bent lever can hold the switch closed.
Ways to stop it coming back
- Hands off the levers before you press power. Set the bike steady, let go of both levers, then switch on.
- Check the levers spring back fully every few rides. Squeeze each lever and let go; both should snap back cleanly. If one is slow, clean around the pivot.
- After any handlebar work, check the lever connector is seated and the cable is not pinched.
- Keep the handlebar area dry. After a wet ride, wipe the levers and cable ends and let them dry before the next switch-on.
- Replace a lever whose switch sticks. If a lever returns freely and the code still comes back, the switch inside it is the suspect — a shop fits a replacement lever with the switch included.
- Never force a connector apart. Rad’s published method is to pull the two halves directly apart, without twisting, line up the notch and arrows, and push them straight back together.

How much checking do you actually need?
Less than most riders expect. The minimum test is one restart with both levers released. If the code clears, the fault was the switch-on state and no part is needed — the only fix is the habit of switching on with hands off the levers. If it comes back with the levers released, the manual’s answer is to contact Rad, because there is no further published owner test. A stuck lever is the one exception an owner can fix; everything else — a stuck switch, a damaged cable, a controller misread — is a shop or Rad job.
Readers also ask
What does Rad Power Bikes error 25 mean? The 2019 RadWagon manual defines it as “brake switch fault, or brake applied while turning on” — the code for the brake lever’s cutoff switch. It appears either because the brake was pulled at switch-on or because the switch or its wiring has a fault.
Can I keep riding with error 25 showing? No. Rad’s manual says to stop riding and contact Rad whenever an error code is displayed. Do not ride with the code showing.
Why does error 25 appear when I switch the bike on? Because a brake lever was pulled at the moment of switch-on. Release both levers and restart, and the code should clear.
What if error 25 comes back with the levers released? Then the switch or its wiring is the suspect — a stuck switch, a lever that does not return, a loose or wet connector, or a damaged cable. The manual gives no further owner step, so contact Rad or take the bike to a shop.
Does Rad publish a guide for error 25? No. Rad’s Help Center has guides for errors 21, 22 and 23 only. For 24, 25 and 30 there is no official guide — only the manual’s definition.
As an Amazon Associate, this site earns from qualifying purchases.
Additional Details
- Name: Rad Power Bikes Error 25: Brake Switch Fault — What the Code Means and How to Check It
- Description: Rad Power Bikes error 25 means a brake switch fault, or the brake applied while switching on. What the code means, the checks in order, and when to contact Rad.
- Published: 22 November 2026






