Part of our guide on E-Bikes.
A Bosch ABS error 810 or 820 usually appears at the worst moment: the display shows the code, the ABS light stays on, and you wonder whether the brakes still work. Both codes point at the wheel speed sensors, not at the brakes. Most of the time the cause is visible at the front wheel: a sensor disc that is missing, dirty or bent, or a wire that has been pulled.
This guide explains what each code means in Bosch’s own words, how to tell 810 from 820, and the checks to work through in order. It follows the Bosch manuals for the Kiox, Purion and Intuvia displays.
Quick facts
| Fact | What it means for your ride |
|---|---|
| Problem this guide fixes | ABS error 810 or 820, with the ABS warning light on |
| What 810 means | Implausible signals from the front wheel speed sensor |
| What 820 means | A fault in the wire to the front wheel speed sensor |
| Check first | Front wheel seating, the sensor disc, and the sensor wire |
| Most common causes | A missing, dirty or bent sensor disc, or a pulled wire |
| Stop and get help | A Bosch dealer must check it if the code stays |
| Related guides | Commuter E-Bike Battery Problems, Disc Brake vs Rim Brake After Rain |
Quick recap
- Error 810: the wheel speed signals do not make sense.
- Error 820: the wire to the front wheel speed sensor has a fault.
- Both codes are about the front wheel speed sensor, not the brakes.
- Check the sensor disc first: present, clean, flat, fitted right.
- After any fix, restart and ride two minutes. The ABS light must go out.
- If the code stays, a Bosch dealer must read the live sensor data.
The short answer: 810 is the sensor signal, 820 is the wire
Bosch’s manuals draw a clear line. Error 810 means “implausible signals from the wheel speed sensor”: the speed readings do not add up. Error 820 means “fault in the wire to the front wheel speed sensor”. Code 810 is usually a disc, gap, or wheel problem; 820 is usually a cable problem.
Codes 821 to 826 mean implausible signals from the front wheel speed sensor. Bosch lists three causes: a sensor disc missing, defective, or fitted incorrectly; front and rear wheels that differ significantly in diameter; or extreme riding, such as riding solely on the rear wheel.

How to diagnose Bosch ABS error 810 and 820, step by step
Work through these steps in order, and note which code is showing.
- Read the code and the light. Note whether the display shows 810, 820, or one of the 821 to 826 codes.
- Check the front wheel seating. Reseat the wheel fully in the dropouts and tighten the axle to the manual’s torque.
- Look at the sensor disc. Check that the slotted ring on the brake disc is there, not bent, and fitted the right way round.
- Clean the sensor disc and sensor face. Wipe both with a clean, dry cloth.
- Check the sensor gap and bracket. The sensor should sit close to the disc and straight; workshop guides put the gap at roughly 1 mm.
- Follow the wire from the sensor. Trace the thin wire up the fork and look for a pulled plug, a kink, or a cut.
- Restart and ride for at least two minutes. The ABS light must go out during this ride. If the code comes back, book a dealer.
If every step looks normal and the code stays, get a Bosch dealer to read the live data.
What you’ll need
- Your Bosch manual and the tool for your thru-axle
- A clean, dry cloth for the sensor disc and sensor face
- A replacement sensor magnet, if the disc is missing or damaged
The sensor magnet below is the 6-bolt type made for Bosch e-bike systems.
What the symptom usually means
Match what you notice with what to try first.

| Situation | What you’ll notice | What to try |
|---|---|---|
| 810 after a wheel change | ABS light on after the wheel came off | Check the sensor disc and wheel seating |
| 810 after mud or a wash | ABS light on after rain or mud | Clean the sensor disc, then test-ride two minutes |
| 820 at any time | ABS light on after a knock | Follow the wire; book a dealer if damaged |
| 810 with a new front wheel | ABS light on after a new wheel or tyre | Check the diameter matches and the disc moved over |
Some Bosch bikes read speed from a spoke magnet. If yours does, the magnet must sit on a spoke where the sensor can see it; one that slid off gives the same signal as a missing disc.
How wheel size, a new wheel and hard riding change the answer
The ABS unit compares the front and rear wheel speeds, and it expects the two to agree. Bosch lists a significant difference in diameter between the front and rear wheels as a cause of the 821 to 826 codes. A different-size front wheel or a much larger tyre gives the unit two speeds that do not match.
Hard riding changes the answer in the same way. Riding solely on the rear wheel, a long wheelie, or a stoppie gives the unit a front wheel speed of nearly nothing while the rear wheel is still turning. A code that appears only then and clears after a normal ride is the system working as designed.
What works
- Keep the front and rear wheel diameters matched, and move the disc to a new wheel
- After a wheel change, reseat the wheel and check the sensor disc
- Clean the sensor disc after muddy rides, before the dirt dries
What to watch
- Do not fit a different-size front wheel without a dealer setup
- Do not ignore a code that appears on every ride
- Do not ride hard to “test” the ABS while the warning light is on
Settings and controls that affect the ABS warning
Before deciding the sensor is faulty, check the settings that decide what the ABS unit expects. Your display holds a wheel circumference setting: how far the bike travels for each wheel turn. If it does not match the tyres fitted, the speeds the system calculates will not match what the sensors report.

The display is part of the diagnosis too. After the two-minute test ride the ABS light must go out; a light that stays on means the fault is still there. If the display is blank, or the light never comes on, check code 890: the ABS indicator light may be defective or missing.
What works
- Check the wheel circumference setting matches the tyres fitted
- Watch the ABS light during the test ride, and trust a fix only when it goes out
What to watch
- A wheel circumference setting that does not match the tyres can confuse the ABS
- An ABS light that never comes on is a fault by itself
When a fix needs a part or a replacement
Some ABS faults have a simple fix, and some need a part. A dirty sensor disc can be cleaned, a loose wheel can be reseated, and a wrong wheel setting can be corrected. A missing disc, a bent ring, a cut wire, or a sensor that still fails after the test ride needs a matching part.
| Fix | Best use | Limit |
|---|---|---|
| Clean the sensor disc and sensor face | Code 810 after mud, rain, or a wash | Will not help if the disc is missing or bent |
| Reseat the front wheel | Code 810 after a wheel change or a knock | Will not help if the disc or wire is damaged |
| Replacement sensor magnet or disc | Sensor disc missing or bent | Must match your system: 6-bolt disc or spoke magnet |
| Replacement sensor wire | Code 820, or a visible cut or pulled plug | A damaged wire is a dealer job |
What works
- Keep the manual with the bike, so a replacement matches the label
- Ask a dealer to test the sensor and wiring before buying a part
- After any fix, start with a short, gentle ride and check the ABS light
What to watch
- A magnet that fits the disc is not proof it matches your system
- A second-hand sensor or disc can carry the same fault you are fixing
- Do not keep riding with the ABS light on and hope it clears
The magnet below fits 6-bolt rotors.
The verdict
Bosch ABS error 810 usually means the front wheel speed signal does not make sense, and 820 usually means the wire to the front wheel speed sensor has a fault. Check the sensor disc, the wheel seating, and the wire first; if the code stays, a Bosch dealer is the right next step.
Readers also ask
Can I still ride with Bosch ABS error 810 or 820?
Your brakes still work as ordinary brakes, but the ABS is switched off while the warning light is on.
What is the difference between Bosch ABS error 810 and 820?
Error 810 means the wheel speed signals do not make sense, usually because of the sensor disc or the gap. Error 820 means the wire has a fault.
Why does error 810 appear after I change a tyre or a wheel?
The sensor disc sits on the brake disc, so it must move over to the new wheel. A disc left off, fitted backwards, or bent gives a signal the unit cannot use.
Can a different front wheel size cause error 810?
Yes. Bosch lists a significant difference in diameter between the front and rear wheels as a cause of the 821 to 826 codes.
When should I take an ABS error to a dealer?
When the code stays after the sensor disc, wheel seating, wire, and wheel setting have been checked. Codes 800, 840, 850 always need a dealer.
Affiliate Disclosure: We may earn a commission when you buy through links on this site, at no extra cost to you.
Additional Details
Name: Bosch ABS Error 810 and 820: Wheel Speed Sensor Faults and How to Fix Them
Description: Bosch ABS error 810 and 820 explained: what the wheel speed sensor codes mean, how to check the sensor disc, wire and wheel, and when a dealer must take over.
Published: November 22, 2026






